°µÍø½ûÇø C60
°µÍø½ûÇø C60 is a pre-mixed cement based non-shrink bedding mortar suitable for the support of road ironwork and highway furniture.
The mixed mortar, when laid, will harden in approximately 10 minutes. The compressive strength gain will reach 20N/m2 within 1 hour allowing early opening of roads to vehicular traffic. The self-contained product only needs to be mixed with water on site and the rapid setting assists the re-bedding of manhole frames and the setting of new frame systems. The product is chloride free and can be safely used with cast iron and steel units.
- Re-bedding of raised manhole frames.
- Bedding of frames in new roads.
- Support of road furniture.
Laitance and all loose material including dust, oil and grease should be removed in order to produce a sound substrate. The work area should be rewetted taking care to remove any standing water before placing the °µÍø½ûÇø C60 mortar. To achieve the most consistent mortar mix, mechanical mixing is recommended.
Thorough hand mixing is suitable but care should be taken to ensure that the mix is fully wetted out without the use of excess water. Mechanical mixing may be carried out in a suitable vessel using a slow speed high torque drill and Mortar Stirrer. Hand mixing may be carried out using a clean spot board or wheelbarrow. Each 25kg bag of °µÍø½ûÇø C60 requires 2.5 to 3.0 litres of water to give a mortar consistency.
Excess water should not be added once setting of the mortar has commenced, further mixing should not be used to re-work the mix. The mortar should be placed within approximately 10 minutes of mixing. The working time may be extended in cold ambient conditions and may be slightly shortened in hot ambient conditions.
Set suitable levelling shims onto the working surface ready to receive the frame or unit. Place the mixed mortar onto the prepared surface and lower the frame or unit onto the mortar and knock down onto the pre-set shims to line and level. The bed thickness applied in a single application should be between 15mm to 75mm.
Thicker support beds can be achieved by applying further material as soon as the lower bed has hardened sufficiently not to damage the original bed. The placed mortar will have hardened sufficiently to carry out further work, such as haunching, within 20 minutes depending on the surrounding ambient conditions. Alternatively thicker beds may be formed by adding clean dry pea shingle up to a maximum of 30% of the weight of the °µÍø½ûÇø C60. No additional water is required for mixing. After placement no special curing is required in moderate ambient conditions.
The placed mortar will have hardened sufficiently to carry out further work, such as haunching, within some 20 minutes depending on the surrounding ambient conditions.
Curing: No special curing is required at temperatures between 5°C and 35°C. For placing at temperatures outside this range, contact our National Sales Office on 01925 632616.
Each 25kg bag of °µÍø½ûÇø C60 will enable a manhole frame 600mm x 600mm to be raised approximately 25mm. The volume yield of each 25kg bag of °µÍø½ûÇø C60 is approximately 12.75 litres.
°µÍø½ûÇø C60 is supplied in 25kg sack bags (50 x 25kg bags per pallet) and 25kg buckets (40 x 25kg per pallet).
°µÍø½ûÇø C60 will have a shelf life of 6 months when kept in dry conditions at a temperature of 5°C to 35°C.
°µÍø½ûÇø C60 has been tested in accordance with appropriate parts of EN 12390. The product conforms to DTp: HD 27/15. Design Manual for Roads and Bridges V7 Sec 2 3.11 Mortars for bedding ironwork such as manhole cover frames during repairs may be trafficked when the strength is expected to be 20N/mm². For rapid construction, this strength should be achieved within 2 hours. °µÍø½ûÇø C60 will achieve the required strength of 20N/mm² within 1 hour at a temperature of 20°C.
Variations in water content and ambient temperature for particular applications may alter mortar consistency and compressive strength achieved.
Typical Mortar Properties @ 20ºC
| Compressive Strength | 60mins | 20MPa |
| 1 day | 35MPa | |
| 7 days | 45MPa | |
| 28 days | 55MPa | |
| Density | 2200 kg/m³ | |
| Approx. Working Life @ 20ºC | 10 mins | |
For full safety information, please request the °µÍø½ûÇø C60 Safety Data Sheet 120 using the contact information on this webpage.
